Attachable and interchangeable Pulsar Ultra-X850S/-X940S Infrared Illuminators are designed for use with Digisight Ultra N450/ N455, Digisight Ultra N450/N455 LRF digital riflescopes and other compatible Pulsar digital devices.

The IR Illuminators provide additional infrared (IR) illumination during observation with night vision devices in low light conditions (no moon, night, thick cloud etc.) and ensure across the whole field of view.

The design of the illuminator provides the ability to adjust the position of the light spot in the field of view.

Pulsar Ultra-X940S operates in an invisible range providing covert observation.

Pulsar Ultra-X850S/-X940S illuminators make it possible to:

• identify the observed object;
• see the selected object in detail;
• increase the observation range;
• adjust the power of the illuminator depending on the observation conditions;
• adjust the position of the light spot in the field of view.

Pulsar Ultra-X850S/-X940S illuminators have a high-power IR diode providing a better observer-target range.

• IR illuminator
• Pin protective cover
• Carrying case
• Operating manual

1. If a standard IR illuminator is installed on the device, remove it according to the operations manual.
2. If the device does not have an IR illuminator, turn the plug (6) according to the image and pull it in the opposite direction from the device/ batter (Digisight Ultra LRF digital riflescopes).
3. Remove the cover (1) of the quick-release IR illuminator.
4. To do this, lift up the lever (3) gently holding the illuminator cover for the Digisight Ultra N450/N455 LRF digital riflescopes, Forward F455 attachments and Forward FN455 devices. For Digisight Ultra N450/N455 digital riflescopes – pull down the lever (3).
5. Lift up the lever (3) of the IR illuminator.
6. Firmly attach the Pulsar Ultra-X850S/-X940S IR illuminator to the connector (5) in the device or battery (Digisight Ultra LRF riflescope).
7. Pull down/lift up the lever (3) (depending on the model of the device) to fix the IR illuminator on the device.

1. Make sure that the illuminator is mounted and connected to the device. To do this, turn on the device and check that there is no icon on the display.
2. To turn on the IR illuminator, briefly press the ON/OFF (2) button on the end of the illuminator. When turning on the power level is minimum ().
3. To switch the power level ( ,  or ), briefly press the ON/OFF (2) button of the IR illuminator.
4. The IR illuminator icon showing the appropriate power level ( ,  or ) is displayed in the status bar on the display of the digital device.
5. To align the position of the light spot in the field of view, turn the lens lock knob (4) of the IR illuminator to the OPEN position.
6. By rotating the lens of the IR illuminator, achieve the required position of the light spot in the field of view. After successful adjustment, rotate the lock knob towards the CLOSE while holding the lens in the desired direction to lock the IR illuminator lens.
7. To turn off the illuminator, press and hold the ON/OFF (2) button on the end of the illuminator.

Notes:

• When the IR illuminator is turned off or removed, the power level is not saved in the memory of the device.
• The infrared illuminator is powered by the digital device.

1. To remove the Pulsar Ultra-X850S/-X940S illuminator, lift up or lower down the lever (3) (depending on the type of the device). Gently pull the illuminator away from the device.
2. Mount the connector plug (6) of the IR illuminator on the digital device.
3. Mount the cover (1) on the IR illuminator. To do this, insert the cover and lock it by lifting up the lever (3).
4. The status bar will show an icon of the disconnected IR Illuminator ().

• Keep water away from the device. This can disable it.
• Independent alterations or repair of the illuminator are prohibited.
• Contact the manufacturer for qualified support if any issues arise.

• Clean the outer surface with a cloth slightly soaked in synthetic detergent.
• Flick the dust off the lenses with a soft brush.
• If necessary, clean the lens with a soft cotton cloth moistened with ethyl alcohol or special multi-layer lens liquid.
• Condensation may form on optical surfaces when moving the illuminator from cold to warm. It is a common occurrence and the condensate should disappear within an hour.

For technical support please contact [email protected].

Answers to frequently asked questions about the devices can also be found in the FAQ section.

Updates of the Product. The manufacturer reserves the right at any time, without mandatory prior notice to the Customer, to make changes to the package contents (subject to the applicable laws, if any), design and characteristics that do not impair the quality of the Product.

Repair. Repair of the product is available within 5 years after purchase of the product.

Limitation of Liability. Subject to mandatory applicable laws and regulations: manufacturer will not be liable for any claims, actions, suits, proceedings, costs, expenses, damages or liabilities (if any), arising out of the use of this product. Operation and use of the product are the sole responsibility of the Customer. Manufacturer’s sole undertaking is limited to providing the product(s) and related services in accordance with the terms and conditions of concluded transactions, including provisions established in warranty. The provision of products sold and services performed by Manufacturer to the Customer shall not be interpreted, construed, or regarded, either expressly or implied, as being for the benefit of or creating any obligation toward any third party (other than Distributor, Dealer, Buyer). Manufacturer’s liability hereunder for damages, regardless of the form or action, shall not exceed the fees or other charges paid to Manufacturer for the product(s) and/or service(s).

MANUFACTURER WILL NOT BE LIABLE FOR LOST REVENUES OR INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, OR PUNITIVE DAMAGES, EVEN IF THE MANUFACTURER KNEW OR SHOULD HAVE KNOWN THAT SUCH DAMAGES WERE POSSIBLE AND EVEN IF DIRECT DAMAGES DO NOT SATISFY A REMEDY.