PULSAR DIGEX C50 (discontinued) Manual

The Digex C50 Digital riflescope is designed for round-the-clock use.

These riflescopes are designed for hunting, target shooting and recreational shooting, observation and orientation.

The riflescope supports day and night observation modes and colour and black and white images.

In deep twilight, when the human eye is already unable to discern details of observed objects, the Digex C50 displays a bright image with correct colour rendering, prolonging hunting time into the night.

In night conditions (absence of starlight, moonlight), it is recommended to use an infrared illuminator with an 850 nm or 940 nm wavelength.

To get started, see the sections:

Battery Charging

Battery Installation

Mounting on the Rifle

Powering on and Image Setting

How to Zero

Stream Vision 2

Ballistic Calculator

1. Eyecup
2. Eyepiece dioptre adjustment ring
3. ON/OFF button
4. REC button
5. ZOOM button
6. Controller
7. Battery compartment cover
8. Battery APS2
9. USB Type-C cover
10. USB Type-C port
11. Objective lens focus ring
12. Aperture adjustment ring
13. Lens cap

• 24/7 use
• Full-colour imaging from sunset till dusk
• High contrast black and white image at night
• High contrast HD AMOLED colour display 1024×768
• Over 500 metre night viewing range
• Variable magnification from 3.5x to 14x
• SumLight™ program algorithm for additional sensitivity improvement
• High-strength aluminium alloy housing
• Heavy caliber shock resistance: 12-gauge, 9.3×64, .375H&H
• Mounting with standard 30mm rings
• Instant start
• Completely waterproof IPX7
• Customisable reticles
• Picture in Picture function
• Device firmware update using the free Stream Vision 2 App*
• Storing photos and videos in Cloud when using the Stream Vision 2 App*
• B-Pack mini combined power system
• Wide operating temperature range -25 °С – +50°С (-13 °F– +122 °F)

* Not available for models without Wi-Fi​

• Stadiametric rangefinder (to estimate distance to object)
• Built-in 3-axis accelerometer gyroscope (slope angle indication)
• Smooth digital zoom
• Large selection of electronic reticles
• Scalable reticles (reticle graduation changes proportional to zoom)
• 5 zeroing profiles (10 distances per profile)
• One-shot zero function
• Precise “Zoom Zeroing” (reducing the minute of angle click value when zeroing at high magnification)
• “Freeze Zeroing” function
• Display Off function
• Wi-Fi. Remote control and observation with a smartphone*
• Display dimming function
• Auto shutdown function
• Ballistic calculator
• Wireless Remote Control (purchased separately)

Video Recording:

• Built-in photo and video recorder with sound recording
• 16GB internal memory
• Integration with iOS and Android devices.

Batteries:

• Built-in 4900 mAh battery pack APS5
• Quick change Li-Ion batteries APS2/APS3
• Built-in and external batteries APS2/APS3 can be charged via USB Type-C

* Not available for models without Wi-Fi

• Only use the charger supplied with the Battery Pack. The use of any other charger may irreparably damage the Battery Pack or the charger and may cause fire.
• Do not charge the Battery Pack immediately after bringing it from a cold environment to a warm one. Wait for 30-40 minutes for the Battery Pack to get warm.
• It is not recommended to charge the batteries with a charger connected to the USB port of a computer or laptop. It can damage the computer.
• Do not leave the Battery Pack unattended while charging.
• Never use a modified or damaged charger.
• Do not leave the Battery Pack with a charger connected to the power adapter after charging is complete.
• Do not expose the Battery Pack to high temperatures or an open flame.
• Do not submerge the Battery Pack in water.
• Do not connect an external device with a current consumption that exceeds permitted levels.
• Do not dismantle or deform the Battery Pack.
• Do not drop or hit the Battery Pack.
• Keep the Battery Pack out of the reach of children.

• During long-term storage, the Battery Pack should be partially charged – the charge level should be between 50% and 80%.
• Charge the Battery Pack at a temperature from 0° C to +45° C (32° F to +113° F), otherwise the battery life will decrease significantly.
• When using the Battery Pack at sub-zero (sub 32° F) temperatures the battery capacity decreases. This is normal and is not a defect.
• Do not use the Battery Pack at temperatures above those shown in the table – this may decrease battery life.
• The Battery Pack is short circuit protected; however, any situation that may cause short-circuiting should be avoided.

Digex C50 digital riflescopes come with a built-in rechargeable lithium-ion Battery Pack APS5 and a removable rechargeable lithium-ion APS2 Battery Pack. The batteries should be charged before first use.

The icon in the status bar will flash when the battery is low. The batteries need to be charged.

1. Open the USB Type-C cover (9) by turning it counterclockwise.
2. Connect the USB Type-C plug of the USB cable (17) to the USB Type-C port (10) in the body of the riflescope.
3. Connect the second USB plug of the USB cable (17) to the USB port on the power adapter (18) by removing the USB Type-A adapter.
4. Plug the device into a 100–240 V socket.
5. Wait until the batteries are fully charged (indication in the status bar: ).

Attention! When charging rechargeable batteries with a USB Type-C connector (10) in the riflescope body section, charging priority is given to the built-in battery. When the device is off, both batteries are charged at the same time. When using the device, the external battery is discharged first.

The rechargeable lithium-ion APS2 and APS3* Battery Packs may be recharged using the APS** charger

1. Insert the Battery Pack (8) along the rail into the APS charger (14) slot as far as it will go. The APS charger is supplied with your device or purchased separately.
2. Point A on the battery and point B on the charger should match.
3. Two batteries*** can be charged at the same time: the second slot is designed for it.
4. Connect the USB Type-C plug of the USB cable (17) to the port (15) of the charger (14).
5. Connect the second plug of the USB cable (17) to the USB port on the power adapter (18).
6. Plug the device into a 100-240 V socket.
7. The LED indicator (16) will display battery charge status.
8. Wait until the battery is fully charged (LED indication (16): ).

(16) LED Indicator****	Battery Charge Status
	Battery level is from 0% to 10%. Charger is not connected to a power supply.
	Battery level is from 0% to 10%. Charger is connected to a power supply.
	Defective battery. Do not use the battery.
	Battery level is from 10% to 20%.
	Battery level is from 20% to 60%.
	Battery level is from 60% to 95%.
	Battery completely charged. Charging will automatically stop. The battery can be disconnected from the charger.

* Purchased separately

** Included in the delivery package.

*** Purchased separately for models without an IR illuminator.

**** LED indicator displays the current battery charge status for 30 seconds when the APS charger is not plugged in. When the power is being supplied, the indicator is constantly displaying the current battery charge status, the LEDs are additionally flickering to display the battery charging process.

1. Turn the battery cover (7) counterclockwise and remove it.
2. Install the battery (8) into the battery compartment along the special guides in the device body designed for it.
3. When properly installed, the battery is fixed in the battery compartment of the device.
4. Close the battery cover (7) by turning it clockwise.

Digex C50 riflescopes are powered by 2 batteries: built-in Battery Pack APS5 and removable Battery Pack APS3/APS2.

1. If there are two batteries in the device, two battery icons are displayed in the status bar (1 – built-in battery, 2 – removable battery). The device battery is displayed in grey and white; it is grey when inactive.
2. When there is no removable battery in the device, only one icon for the built-in battery displays in white in the status bar.
3. When both batteries are fully charged, the device is powered by the removable battery. If there is low removable battery level, the device will switch to the built-in battery.
4. Battery charge level is displayed in % above the icon in the status bar while charging.
5. It is possible to replace the removable battery even while the device is on.

Attention!  When installing a removable battery with a sufficient charge level, the device will automatically switch to it.

Power can be supplied from an external source such as a 5 V or 9 V power bank.

1. Connect the external power supply to the USB Type-C port (10) of the riflescope.
2. The riflescope switches to external power source, while built-in Battery Pack APS5 and removable Battery Pack APS2 (or APS3*) will gradually recharge.
3. A rechargeable battery icon indicating a percentage of the battery life will appear in the status bar.
4. When you turn off external power source, the riflescope switches over to the removable battery without turning off. When there is no removable battery or low power level the device switches to the built-in battery.

*Optional

Attention! Charging Power Bank APS2 / APS3 / internal APS5 batteries at air temperatures below 0 °C can result in reduced battery life. When using external power, connect Power Bank to the switched-on riflescope, which have worked for several minutes.

To ensure accurate shooting the Digex С50 riflescope should be properly mounted on the rifle.

• The riflescope is fixed using the mount, which is purchased separately. Use only high-quality mounts and rings that are designed specifically for your rifle. Follow the mounting manufacturer’s recommendations on the installation procedure and use the proper tool.
• When mounting the riflescope, adjust the position on the rifle so that proper (comfortable) holding of rifle ensures the distance between the riflescope and eye (eye relief) specified by the Technical Specifications. Failure to comply with this recommendation may result in injury to the shooter by the parts of the riflescope eyepiece when shooting.
• It is recommended to install the riflescope as low as possible, at the same time it should not be in contact with barrel or receiver.
• In order to avoid pinching the riflescope body, a tightening torque for the screws of the mounting rings must be not more than 2.5 Nm (22.1 Pound-force inches). A torque wrench is recommended to control the tightening torque.
• Before using the riflescope when hunting, follow instructions in the Zeroing section.
• Use of a removable eyecup is recommended (1) to eliminate backlight from the display.
• It is recommended to use an eyecup while using the riflescope to increase camouflage and avoid detection. Mounting the eyecup on the riflescope eyepiece is carried out using built-in magnets.

1. Open the lens cap (13).
2. Press the ON/OFF (3) button briefly to power the riflescope on.
3. Adjust the sharpness of the symbols on the display by rotating the dioptre adjustment ring of the eyepiece (2).
4. Turn the aperture adjustment ring (12) to select the observation mode (Day –, Night –).
5. Select the image mode (colour/black-and-white) by short pressing the ON/OFF (3) button.
6. Rotate the lens focus ring (11) to focus on the object being observed.
7. Activate the quick menu by briefly pressing the controller button (6) to adjust the brightness and contrast of the display (see the Quick Menu Functions section for details).
8. Repeatedly press the ZOOM (5) button to change the magnification ratio of the riflescope. While the magnifying glass icon  is visible on the screen, rotate the controller (6) for smooth digital zooming from the current magnification.
9. Turn on the IR illuminator* and adjust the lighting power according to its operating instructions to improve the quality of observation in low light conditions.
10. Power the device off with a long press of the ON/OFF (3) button.

* Purchased separately for models without an IR illuminator.

Zeroing at a temperature close to the riflescope’s operating temperature is recommended.

Step 1. Take a shot

1. Shooting from a benchrest is recommended.

2. Set a target at a known distance.

3. Adjust the riflescope according to the Powering on and Image Setting section.

4. Select the zeroing profile (see Reticle & Zeroing -> Zeroing Profile  main menu item)

5. Point the rifle at the center of the target and shoot.

Step 2. Align the reticle with the point of impact

1. Press and hold the controller button (6) to enter the main menu.

2. Add the distance you are aiming at (e.g. 100 meters): Reticle & Zeroing -> Add New Distance . Select the value for each distance digit by rotating the controller ring (6). Press the controller button (6) briefly to switch between digits. After setting the required distance, press and hold the controller button (6) to save it.

3. After adding the distance, it will switch to the Zeroing parameters settings menu . An auxiliary cross  will appear in the center of the display, and X and Y coordinates of the auxiliary cross will appear in the upper right corner.

4. Press the controller button (6) briefly to enter the Windage/Elevation  submenu.

5. While holding the reticle at the aiming point, move the auxiliary cross  until it is aligned with the impact point by rotating the controller ring (6).

6. To change the direction of the auxiliary cross movement from horizontal to vertical, press the controller button (6) briefly.

Zoom Zeroing function:

To improve the accuracy of zeroing, you can change the magnification in the menu . The larger the magnification, the smaller the step of shifting the reticle on the display relative to the image from the sensor.

One-shot “Freeze Zeroing” function:

Using the Freeze function allows you to make adjustments without the need to hold the rifle precisely at the initial aiming point – freezing the zeroing screen (refer to Reticle & Zeroing  menu item => Distance submenu => Zeroing Parameters Settings  submenu => Freeze  submenu or short pressing of the ON/OFF (3) button. The image will “freeze” and the  icon will appear.

Step 3. Save the coordinates

1. Press and hold the controller button (6) to save a new position for the reticle. The reticle will be aligned with the impact point and it will exit the Windage/Elevation  submenu.

2. Press and hold the controller button (6) again to exit the zeroing settings menu – the message “Zeroing coordinates saved” appears, confirming the successful operation.

3. Fire a second shot – now the point of impact and the aiming point must be matched.

Notes:

• After zeroing, the reticle may not be in the center of the display.
• The range of movement of the riflescope reticle allows you to successfully zero the riflescope, even on mounts that are far from ideal, minimizing the possible disadvantages of the mounts. The better the mount is installed, the less you have to move the reticle. We recommend mounting the riflescope as low as possible.

To zero your riflescope, you need to set a zeroing distance first in the range of 1 to 910 m (955 yards).

1. Press and hold the controller button (6) to enter the main menu.
2. Rotate the controller ring (6) to select the Reticle & Zeroing  menu item.
3. Press the controller button (6) briefly to enter the Reticle & Zeroing submenu.
4. Rotate the controller ring (6) to select Add New Distance menu item.
5. Press the controller button (6) briefly to enter the submenu.
6. Rotate the controller ring (6) to select a value for each digit. Press the controller button (6) briefly to switch between digits 
7. Having set the desired distance, press and hold the controller button (6) to save it.

The distance you set first becomes a primary distance – shown with the icon on the right of the distance value.

Note: Maximum number of zeroing distances is 10 for each profile.

1. Press and hold the controller button (6) to enter the main menu.
2. Rotate the controller ring (6) to select Reticle & Zeroing  in the menu. Briefly press the controller button (6) to select it. Zeroed distances are displayed below.
3. The values (e.g., +7.0) shown on the right of the distance values, stand for the number of clicks along the Y axis, at which the reticle position at other distances differs from the reticle position in the primary distance.
4. To zero at any distance again, rotate the controller ring (6) to select the required distance and briefly press the controller button (6).
5. Rotate the controller ring (6) to select the Zeroing Parameters Settings  and enter by briefly pressing the controller button (6).
6. Zeroing screen, which allows the change of zeroing coordinates, will appear:

Adjust the reticle position through the Windage/Elevation  submenu in Zeroing Parameters Settings. For more information, see the How to Zero section.

Magnification allows you to magnify via the device’s digital zoom when zeroing, which reduces the MOA-per-click values of adjustments and improves zeroing accuracy.

1. In the Zeroing Parameters Settings   menu, rotate the controller ring (6) to select the Magnification   submenu item and enter by briefly pressing the controller button (6).
2. Rotate the controller ring (6) to select a digital magnification value of the riflescope (e.g., x4).
3. Press the controller button (6) briefly to confirm your selection.

The minute of angle click when using the Magnification function is indicated in the Table of Technical Specifications.

The “freeze” function allows the user to adjust the reticle on a still image while manipulating the rifle.

1. In the Zeroing Parameters Settings menu, rotate the controller ring (6) to move the cursor to the Freeze function.
2. Align the reticle with the point of aiming and press the controller (6) or ON/OFF (3) button. A screenshot will be taken, an icon will appear.
3. Go to the additional Windage/Elevation   submenu and adjust the position of the reticle (see the How to Zero section).
4. Select the Freeze   submenu item again and briefly press the controller (6) or ON/OFF (3) button – the image will “unfreeze”.

1. In the Zeroing Parameters Settings   menu, rotate the controller ring (6) to select the Name Distance   submenu item and enter it by briefly pressing the controller button (6)​.
2. Rotate the controller ring (6) to select a value for each digit. Press the controller button (6) briefly to switch between digits.
3. Press and hold the controller button (6) to confirm the selection.

1. Press and hold the controller button (6) to enter the main menu.
2. Rotate the controller ring (6) to select the Reticle & Zeroing  menu item and enter by briefly pressing the controller button (6) – zeroed distances are displayed at the bottom.
3. Select a non-primary distance and enter the submenu for operating the distance with a brief press of the controller button (6).
4. Select Change Primary Distance item.
5. Press the controller button (6) briefly.
6. Icon next to the selected distance confirms the change of primary distance.

There will also be a recalculation of corrections in clicks for other distances relative to the new primary distance.

1. Press and hold the controller button (6) to enter the main menu.
2. Rotate the controller ring (6) to select the Reticle & Zeroing   menu item and enter by briefly pressing the controller button (6) – zeroed distances are displayed at the bottom.
3. Select the distance you wish to delete and enter the submenu for operating the distances with a brief press of the controller button (6).
4. Select Delete Distance  item.
5. Press the controller button (6) briefly.
6. Select “Yes” in the appeared dialog box to delete a distance. “No” – to cancel deletion.
7. Press the controller button (6) briefly to confirm your selection.

Attention! If the primary distance is deleted, the first distance on the list automatically becomes the new primary distance.

The status bar is at the bottom of the display and shows information on the actual operating status of the riflescope, including:

1. Actual zeroing profile (e.g., A)

2. Zeroing distance (e.g., 100 m)

3. SumLight™ (on/off)

4. Mode of operation (colour, black and white)

5. Microphone (on or off)

6. Current magnification

7. Wi-Fi connection

8. Bluetooth:

– Bluetooth is on

– the device with Bluetooth is connected

9. Auto Shutdown function (e.g., 5 minutes)

10. Clock

11. Power supply:

• Battery discharge level (when riflescope is powered by a built-in or removable battery).
• External battery power indicator (if the riflescope is powered by an external power supply).
• Battery indicator  with current percentage of charge (when charging from an external power source).
• Battery indicator shows a low battery charge
• Battery indicator shows a low internal battery charge

The basic settings (adjusting brightness and contrast, smooth digital zoom function, stadiametric rangefinder, current profile and distance information) can be changed using the quick menu.

• Press the controller button (6) briefly to enter the quick menu.
• A short press of the controller button (6) enables you to switch between functions, as described below.

Brightness  – rotate the controller ring (6) to change the display brightness value from 00 to 20.

Contrast  – rotate the controller ring (6) to change the image contrast value from 00 to 20.

  – information on the current profile and zeroing distance in this profile (e.g., profile A, zeroing distance of 100 m). This information is always displayed in the status bar. Rotate the controller ring (6) to switch between the zeroing distances in the adjusted profile. This function is available if there are two or more distances in the profile.

Tip: To quickly switch between distances while hunting, leave the Zeroing Distance option selected before exiting the quick menu. The menu item will be saved, and the next time you enter the quick menu, you can quickly switch the zeroing distances by turning the controller (6) (for example, 100 m, 150 m, 200 m).

– change the distance to calculate corrections for the ballistic calculator. Rotate the controller ring (6) to select the distance.

This function is only visible when the ballistic profile is selected.

Stadiametric Rangefinder – rotating the controller ring (6), change the distance between the special mark points to determine the distance to the observed object (for more details on the rangefinder, see the Stadiametric Rangefinder section).

• Press and hold the controller button (6) to exit the menu or wait 10 seconds to exit automatically.

The device has two image modes: colour and black and white.

Toggle between modes:

1. Turn the aperture adjustment ring (12) to select the observation mode (Day – , Night – ).
2. Select the image mode (color/black-and-white) by short pressing the ON/OFF (3) button.

Optimal combinations of modes:

Time of day	Day	Twilight		Night
Observation mode
Image Mode	Colour		Black and white
IR-illuminator	No		Yes

At dusk, turn the aperture adjustment ring (12) to position . You will be able to use colour mode. When the light lowers, switch to black and white.

At night, you can also use an IR-illuminator (included in the package or purchased separately).

Note: In low light conditions, noise may appear in the image. This is normal and not a defect.

1. Install the Stream Vision Ballistics app from Google Play or AppStore.

2. Go to Profiles tab.

3. Create a profile for your riflescope, ammunition and zeroing distance. Make sure that “Ballistic parameters” switch is on. If your ammo is not on the list, you can enter its parameters manually. The more parameters you specify, the more accurate the recommended point of aiming will be.

4. Adjust the temperature, pressure and humidity of the environment while zeroing your riflescope.

5. Enter a profile name and click save .

6. Connect your riflescope to your smartphone using Bluetooth. First, make sure that your riflescope has the latest firmware version 3.3 or higher installed.

7. Load the profile into the riflescope.

To do this, go to the “Devices” tab –> Select your riflescope –> “All device profiles” -> click on the profile you want to replace and select the created profile from the list.

8. Set the status to “Active” for the ballistic profile. To do this, click on the button next to the desired profile, or select it in the profile selection menu in the riflescope.

9. Make sure that the Ballistic Activation option is enabled in the riflescope’s Ballistics menu.

10. Select the desired distance in the quick menu:

• Press the controller button (6) briefly to enter the quick menu.
• Briefly press the controller button (6) to select .
• Rotate the controller ring (6) to select the desired distance.
• Press and hold the controller button (6) to exit the menu or wait 10 seconds to exit automatically.

11. Check the accuracy of your profile settings with a test shot at the shooting range.

Note: profiles for different types of ammunition must be zeroed separately.

12. To activate the use of weather data in your geolocation during the shot, go to the “Devices” tab -> Select your riflescope -> “Set outdoor”.

In the Ballistics section of the main menu, you can configure the following settings of the ballistic calculator:

• Screen position of the measured distance value
• Turn on/off the ballistic calculator
• Correction units
• Reticle type and color for suggested point of aiming.

Stream Vision Ballistics Manual

Android

iOS

The riflescope is capable of video recording and photography. Videos and images are saved on the built-in memory card.

Before using the photo and video functions, read the Date and Time subsections of the General Settings section.

For information on how to watch recorded photos and videos, see the Stream Vision 2 user manual: Android, iOS.

Built-in recorder operates in two modes:

• Photo (photography; the icon is displayed in the upper left corner of the display).

• Video (video recording; the icon is displayed in the upper left corner of the display, the total remaining recording time is given taking into account the current resolution in the HH:MM format (hours:minutes).

Toggle (switch) between the riflescope operating modes with a long press of the REC (4) button. Switching between the modes is cyclical (Video–> Photo–> Video…).

Photo mode. Capturing an image

1. Switch to the Photo mode with a long press of the REC (4) button.

2. Press the REC (4) button briefly to capture a photo. The icon flashes – the photo file is being saved to the built-in SD card.

Video mode. Recording a video

1. Switch to the Video mode with a long press of the REC (4) button.

2. Press the REC (4) button briefly to start video recording.

3. When the video recording starts, the icon ​ will disappear, instead of it the REC icon as well as the video recording timer displayed in the MM:SS (minutes:seconds) format will appear .

4. Pause/continue recording by briefly pressing the REC (4) button.

5. Press and hold the REC (4) button to stop video recording.

Video files are stored in the built-in memory card:

• After turning off the video recording;
• Upon powering the riflescope off if recording was on;
• When the memory card is overfilled during recording (Memory Full message appears on the display).

Notes:

• You can enter and navigate the menu during video recording.
• Recorded videos and photos are saved to the built-in memory card of the riflescope in the format img_xxx. jpg (for photos); video_xxx. mp4 (for video).
• Videos are recorded in clips with a maximum duration of 5 minutes. The number of recorded files is limited by the capacity of unit’s internal memory.
• Regularly check free memory within the built-in memory card and move the footage to other storage media to free up the memory card space.
• In case of a memory card error, you can use the format function in the General Settings section of the main menu.
• When the Display Off function is activated, video recording continues to run in the background.

The riflescope functionality allows you to quickly increase the basic magnification (see Magnification line in the table of Technical Specifications) by 2 and 4 times, as well as to return to the basic magnification.

• Press the ZOOM (5) button successively to change the magnification ratio of the riflescope.
• While the icon is visible on the screen, rotate the controller ring (6) for smooth digital zooming from the current magnification.

Note: the magnification value is reset to the base value when the device is switched off.

The PiP function (Picture-in-Picture) allows you to see both a magnified image in a particular dialog box and the main image.

1. Press and hold the ZOOM (5) button to turn on/off the PiP function.
2. To change the digital zoom in the PiP window, briefly press the ZOOM (5) button or rotate the controller ring (6) until the icon is visible on the screen .
3. The magnified image is displayed in a particular dialog box, with the full magnification being used.
4. The rest of the image is displayed only with the optical zoom (digital zoom is off).
5. When PiP is turned off, the display shows the full magnification set for the PiP mode.

This function darkens the screen, which aids the user’s concealment. However, the device stays on.

1. When the device is on, press and hold the ON/OFF (3) button for less than 3 seconds. The display will turn off, the current time and the “Display off” icon will appear.
2. Press the ON/OFF (3) button briefly to turn on the display.
3. When you press and hold the ON/OFF (3) button, the display shows the “Display off” icon with a countdown. Holding the button down for the duration of the countdown will power the device off completely.

* Not available for models without Wi-Fi

The riflescope has a function for wireless communication with mobile devices (smartphone or tablet) via Wi-Fi.

1. To enable the wireless module, enter the main menu by long pressing the controller button (6).
2. Rotate the controller ring (6) to select the Wi-Fi Activation menu item.
3. Press the controller button (6) briefly to turn on/off Wi-Fi module.

Wi-Fi is displayed in the status bar as follows:

Indication in the Status Bar	Connection Status
	Wi-Fi is switched off
	Wi-Fi is switched on by the user, Wi-Fi connection in the riflescope is in progress.
	Wi-Fi is switched on, there is no connection to the riflescope
	Wi-Fi is switched on, there is connection to the riflescope

• An external device recognizes the riflescope under the name Digex_XXXX, where XXXX are the four last digits of the serial number.
• After entering the password on a mobile device (see Password Setup subsection of the Wi-Fi Settings section for more information on setting a password) and setting up a connection, the icon in the riflescope status bar will change to .
• The Wi-Fi function will turn off automatically if there is not enough battery power for Wi-Fi.
• When Wi-Fi is on, the power supply will switch to the internal battery after the external battery reaches a 20% charge level.

Available for scalable reticles X51Fi-300, M56Fi, M57Fi.

When changing the riflescope digital magnification, the reticle that appears on the display is scaled; the reticle appearance will change (enlarge or reduce) proportionally to the magnification. It allows the use of the rangefinder reticles with any digital magnification.

This function is designed to preserve ballistic properties of the scalable reticles X51Fi-300, M56Fi, M57Fi for all magnifications.

1. Enter the main menu with a long press of the controller button (6).
2. Enter submenu Reticle & zeroing  -> Reticle Type .
3. Select the reticle X51Fi-300, M56Fi, M57Fi.

Please find the available scalable reticles in the catalogue in the Downloads section on our website).

Notes:

• When zooming in and out the image, the selected reticle on the display and in the recorded video changes its geometrical size according to the magnification selected.
• The reticle scale changes both on the main display and in the PiP mode.

The night vision digital riflescope is equipped with a stadiametric rangefinder, allowing you to determine the approximate distance to an object if its size is known.

1. To select the Stadiametric Rangefinder function, enter the Quick Menu by briefly pressing the controller button (6).
2. Press the controller button (6) briefly to select the icon .
3. The display will show the lines for measurements, the icons and numbers of the measured distance for three objects.
4. Place the bottom fixed line under the object.
5. Rotate the controller ring (6) to move the upper line relative to the lower horizontal fixed line so that the object is located directly between the lines. A target range automatically recalculated along with movement.
6. To exit the rangefinder mode, briefly press the controller button (6) or wait 10 seconds to exit automatically.

Notes:

• There are three predefined values for objects: Hare – 0.3 m high, Boar – 0.7 m high, Deer – 1.7 m high.
• The measured range value is rounded off before being displayed – for large range values up to 5 m, for shorter range – up to 1 m.
• To select a unit of measurement (meters or yards), go to the General Settings  menu item => Units of Measure  submenu.

1. Press the ON/OFF (3) button briefly to power the riflescope on (the computer will not detect the riflescope if it is turned off).
2. Connect one end of the USB cable to the riflescope micro USB Type-C (10) and the other one to the port on your computer using a USB Type-A adapter.
3. The riflescope is detected by the computer automatically and no installation of drivers is required.
4. After a few seconds, two connection options appear on the display: Power and Memory card.
5. Rotate the controller ring (6) to select the connection mode.
6. Press the controller button (6) briefly to confirm your selection.

Power

• Upon choosing this mode, your PC is used as an external power supply. An icon will appear in the status bar.
• The riflescope continues operating and all functions are accessible.
• Battery recharge feasibility depends on your computer’s USB port.

Memory Card

• When selecting this mode, the computer recognizes the riflescope as a memory card. This mode is designed to manage the files saved in riflescope’s memory.
• Even though the riflescope is on, its functions are unavailable in this mode. It will continue to operate after being disconnected from the computer.
• If a video was being recorded at the moment of connection, the recording will stop and will be saved.

USB Disconnection

• When the USB is disconnected from the riflescope connected in the Power mode, the riflescope continues to operate on battery packs when they are sufficiently charged.
• If the riflescope is in Memory Card mode and is disconnected from USB, the device will remain on.

* Not available for models without Wi-Fi

Install the Stream Vision 2 application to download files, update firmware, control the device by remote control and broadcast images from your device to a smartphone or a tablet via WiFi.

We recommend using the latest version – Stream Vision 2.

You can find further guidelines on Stream Vision 2 here.

Download from Google Play

Download from App Store

Find answers to frequently asked questions about using Stream Vision 2 here.

Stream Vision 2 Manual

Android

iOS

* Not available for models without Wi-Fi

1. Download the free Stream Vision 2 App in Google Play or App Store.
2. Connect your Pulsar device to your mobile device (smartphone or tablet).
3. Launch Stream Vision 2 and go to section “Settings”.
4. Select your Pulsar device and press “Check firmware update”.
5. Wait for the update to download and install. Pulsar device will reboot and will be ready to operate.

Important:

• if your Pulsar device is connected to a phone or mobile device, please turn on mobile data transfer (GPRS/3G/4G) to download update;
• if your Pulsar device is not connected to your phone or mobile device but is already listed in “Settings” > “My devices” section, you may use Wi-Fi to download update.

Find answers to frequently asked questions about using Stream Vision 2 here.

Is your firmware up to date?

Click here to check the latest firmware for your device.

It is recommended to inspect your riflescope before each use. Check the following:

• The device should be free of any cracks or deformations.
• The lenses should be free of cracks, grease, dirt or debris.
• The state of rechargeable batteries (should be fully charged). Electrical sockets should be free of salts, oxidation, or other debris.
• All controls should be responsive.

Maintenance should be carried out at least twice a year and should include the following steps:

• Wipe the exterior surfaces of metal and plastic parts with a cotton cloth. Do not use chemically active substances, solvents, etc. as these will damage the paint.
• Clean the electrical contacts of the battery and battery slot on the riflescope and IR illuminator using a non-greasy organic solvent.
• Check the lenses of the eyepiece, objective and IR illuminator. If necessary, remove dust and sand from the optics (it is preferable to use a non-contact method). Cleaning of the exterior surfaces of the optics should be done with cleaners designed especially for this purpose.

Possible cause
The Battery Pack is empty.
Solution
Charge the Battery Pack.

Solution
In case of any malfunctions during operation, try resetting the device by long pressing the ON/OFF button for 10 seconds.

Possible cause
USB cable is damaged.
Solution
Replace USB cable.

Possible cause
The external power supply is discharged.
Solution
Charge the external power supply.

Possible cause
The dioptre adjustment range is not enough for your eyesight.
Solution
If you wear glasses with a range of -3/+5, keep glasses on when looking through the eyepiece.

Possible cause
Condensation on the external surface of the eyepiece lens.
Solution
Wipe the lens with a cloth.

Possible cause
The device was exposed to static electricity during operation.
Solution
After exposure to static electricity, the device may either reboot automatically, or require turning off and on again.

Possible cause
Brightness or contrast level is too low.
Solution
Adjust the brightness or contrast in the Quick Menu.

Possible cause
The aperture is closed during night observation.
Solution
Open the aperture by turning the control ring to the position  .

Possible cause
Dust and condensate are covering the outside or inside optical surfaces.
Solution
Wipe the outer surface of the objective lens with a soft cotton cloth. Dry the riflescope. Let it stand for four hours in a warm room.

Possible cause
The lens is not focused.
Solution
Adjust the image sharpness by rotating the lens focus ring.

Possible cause
The riflescope is not mounted securely or the mount was not fixed with thread sealant.
Solution
Check that the riflescope has been securely mounted.
Make sure you are shooting the same cartridge and load as when the weapon was first zeroed.
Be advised that changes in season, time of day and/or changes in temperature may slightly shift your point of impact. Double checking your zero before hunting is recommended.

Possible cause
After shooting, the aiming reticle may not be in the centre of the display. This is normal and is not a defect.

Possible cause
Wrong settings.
Solution
Adjust the riflescope according to the Powering on and Image Setting section. Check the outer surfaces of the objective lenses and eyepiece and, where necessary, wipe them from dust, condensation, frost, etc. In cold weather, you can use special anti-fogging coatings (e.g., the same as for corrective glasses).

Possible cause
Password in the riflescope was changed.
Solution
Delete network and connect again inserting the password saved in the riflescope.

Possible cause
There are too many Wi-Fi networks in the area where the riflescope is located which may cause signal interference.
Solution
To ensure stable Wi-Fi performance, move the riflescope to an area with few or no Wi-Fi networks.

Possible cause
The device has a 5 GHz network enabled, but the smartphone only supports 2.4 GHz.
Solution
Switch the device’s Wi-Fi bandwidth to 2.4 GHz.

More information on solving problems with connection to Stream Vision 2 by following the link.

Possible cause
Smartphone or tablet is out of range of a strong Wi-Fi signal. There are obstacles between the device and the smartphone or tablet (e.g., concrete walls).

Solution
Relocate smartphone or tablet into the Wi-Fi signal line of sight.

More information on solving problems with connection to Stream Vision 2 by following the link.

Possible cause
These problems may occur during the observation in adverse weather conditions (snow, rain, fog etc.).

Solution
Presence of dots is caused by peculiarities of sensor or display production technology and is not a defect.

Possible cause
The Bluetooth module is not turned on.
Solution
Turn on the Bluetooth module according to the instructions (see the Bluetooth section).

Possible cause
The Remote control is not activated.
Solution
Activate the remote control according to instructions (see the Remote Control Activation section).

Possible cause
The Remote Control is out of range of the device.
Solution
Return to the device coverage area.

Possible cause
Remote control battery low.
Solution
Install a new CR2032 battery as follows: unscrew the screws on the rear cover of the Remote Control, remove the cover, install a new battery, and screw the cover with screws.