PULSAR KRYPTON 2 MONOCULAR XG50 Manual

The Krypton 2 thermal imager is designed for a variety of applications, including hunting surveillance, security activities, day and night photo and video shooting.

The Krypton 2 thermal imaging module can be mounted (using the correct Ring Adapter) on to the objective lens housing of various daylight optical devices, converting them into a highly-sensitive thermal imaging device.

To get started, see the sections:

Battery Charging

Battery Installation

Installing the Monocular on to the Thermal Imaging Module

​Mounting the Adapter on the Device

Mounting the Thermal Imaging Module on the Adapter​​​

Powering on and Image Setting

Stream Vision 2

• Thermal Imager
• Pulsar 3×20 B Monocular
• Single-point neck strap
• Carrying Case
• Wireless Remote Control
• IPS7 Battery Pack
• Battery Pack Charger
• Power Adapter
• USB Type-C cable with USB Type-A adapter
• USB Type-C to MicroUSB Type-B adapter
• Quick Start Guide
• Lens-Cleaning Cloth
• Warranty Card
• Allen Key S3

1. Lens cover
2. Eyepiece cover
3. Battery locking lever
4. Battery pack
5. UP/REC button
6. MENU button
7. DOWN/MODE button
8. ON/OFF/Calibration button
9. Lens focus knob
10. USB Type-C port
11. Objective lens end of daylight optical device*
12. Insert**
13. Adapter**
14. Screw**
15. Tightening screw**
16. Screw**
17. Adapter lever**
18. Mount**

*Not included in the package contents

**Items of PSP B Ring Adapter (available separately)

• Easily converts daylight optical devices into thermal imaging devices
• Preserves the benefits of daylight optics in night-time conditions
• Three calibration modes (manual, semi-automatic and automatic)
• 3 levels of sensitivity enhancement: Normal, High, Ultra
• Compatible with a wide range of daylight optical magnifications
• Wireless remote control
• Instant start
• Display off function
• Built-in video recording
• Remote Firmware update
• Fully watertight (IPX7 protection class)
• Wide operating temperature range (-25 °С – +50°С)

Video/audio recording

• Built-in video recorder
• Integration with iOS and Android devices
• Wi-Fi Smartphone remote control and surveillance
• Storing photos and videos in Cloud when using the Stream Vision 2 App

Battery Pack

• Quick-change IPS7 Li-ion battery pack
• Charging via USB Type-C port

• Always use the IPS charger supplied with the device (or purchased separately) to charge IPS batteries. Using an unsuitable charger can cause irreparable damage to the battery and fire.
• Do not charge the battery immediately after bringing it from cold to warm. Wait at least 30 minutes for the battery to warm up.
• Do not leave the battery unattended while charging.
• Do not use the charger if it has been modified or damaged.
• Do not leave the battery in a charger connected to the network after charging is complete.
• Do not expose the battery to high temperatures and naked flame.
• Do not use the battery as a power source for devices that do not support IPS7 batteries.
• Do not disassemble or deform the battery.
• Do not drop or strike the battery.
• Do not submerge the battery.
• Keep the battery out of the reach of children.

Attention! Please do not use the IPS 14 Battery Pack with the Krypton 2 FXQ35/FXG50 due to the battery´s heavy weight.

• The battery should be partially charged for long-term storage – 50 to 80 %.
• The battery should be charged at an ambient temperature of 0 °C…+35 °C (+32 °F…+95° F). Otherwise, lifespan of the battery will decrease significantly.
• When using the battery at sub-zero temperatures, the battery capacity decreases, this is normal and not a defect.
• Do not use the battery at temperatures outside the range of -25 °С…+50 °С (-13 °F…+122 °F) – this may reduce battery’s life.
• The battery has a short-circuit protection. However, any situation that may cause short-circuiting should be avoided.

The device is supplied with a rechargeable IPS7 Lithium-ion Battery Pack which allows the device to be used for up to 11 hours. Charge the battery before first use.

The icon  in the status bar will flash when the battery is low. The battery needs to be charged.

Option 1

1. Install the IPS7 battery (4) in the battery compartment of the device.
2. Connect the USB Type-C cable (20) to the USB Type-C connector (10) of the device.
3. Connect the other end of the USB cable (20) to the Power Adapter (21) by removing the USB Type-A adapter.
4. Plug the Power Adapter (21) into a 100-240 V socket.
5. Wait until the battery is fully charged (indication in the status bar: ).

If the device is off, the LED indicator will display the battery charge status:

LED indication	Battery status
	Battery is charging
	Battery is charged
	Defective battery. Do not use the battery!
–	The device is switched on

Option 2

Charging

Step 1. Install the battery into the charger

1. Move the lever (3) to the open position .
2. Install the Battery Pack (4) into the charger.
3. Lock the battery (4) by moving the lever to the closed position .

Step 2. Сheck the current battery level

• Upon installation, a green LED indicator on the charger will start to glow and begin flashing:

– once if the battery charge ranges from 0% to 50%.

– twice if the battery charge ranges from 51% to 75%.

– three times if the battery charge ranges from 76% to 99%.

• When the indicator is continuously green, the battery is fully charged. Disconnect the charger from the mains and disconnect the battery from the charger.
• If the battery charger indicator is constantly red when the battery is inserted, the charge level is probably below the permissible level (the battery has been in a discharged state for a long period of time). Leave the battery in the charger for a long period of time (up to several hours), then remove and reinsert.
• If the indicator begins to flash green, the battery is good.
• If it continues to show red, the battery is defective. Do not use this battery!

The LED indicator will display the battery charge status:

LED Indicator	Battery Charge Status
	Battery is empty
	Battery charge level is from 0% to 50%
	Battery charge level is from 51% to 75%
	Battery charge level is from 76% to 99%
	Battery is full

Step 3. Сonnect the charger to the mains supply

1. Connect the plug of the USB Type-C cable (20) with the attached MicroUSB adapter (22) to the USB socket (19) of the charger.
2. Connect the other end of the USB cable (20) to the power adapter (21).
3. Plug the power adapter (21) into a 100-240V socket.
4. When the indicator is continuously green, the battery is fully charged. Disconnect the charger from the mains.

1. Move the lever (3) to the open position .
2. Insert the battery (4) into the slot provided for it on the body of the device in such a way that element D (protrusion on the battery case) is on the left.
3. Lock the battery (4) by moving the lever (3) to the closed position .

External power is supplied from an external source, such as a 5V Power Bank.

1. Attach the external power source to the USB Type-C connector (10) on the device.
2. The device will switch to operation from the external power supply, while the IPS7 battery will be gradually recharged.
3. A battery icon  will appear on the display showing charge level as a percentage.
4. If the device is operated from an external power source and the IPS7 battery is not connected, an icon  is displayed.
5. Once the external power source is disconnected, the device will begin functioning on battery power.

Attention! Charging Power Bank IPS7 batteries at air temperatures below 0 °C can result in reduced battery life. When using external power, connect Power Bank to the switched-on device, which have worked for several minutes.

The Pulsar 3×20 B monocular (23) allows you to transform the device into a hand-held thermal imager with 3x magnification.

1. Align the protrusions on the monocular (23) on the side of its lens with the grooves of the mount (18) of the thermal imaging module.

2. Turn the monocular clockwise to secure it on the thermal imaging module. The recommended position of the clamping screw (24) is at the bottom (see Figure).

3. Turn on the thermal imaging module by pressing the ON/OFF (8) button.

4. Adjust the eyepiece diopter ring (25) until the symbols in the display are sharp.

5. Loosen the screw (24) with an Allen key S3.

6. Align the display to the center of the image in the monocular by tilting the thermal imaging module in the required directions.

7. Lock the monocular in the chosen position by tightening the screw (24) until it stops (clamping force – 2.5 Nm/ 22.13 in-lbs).

8. To remove the monocular, turn it counterclockwise and disconnect from the thermal imaging module.

Note: if you wish to use a third-party adapter or a Pulsar PSP Ring Adapter, unscrew the ring (A) near the mount assembly (18).

Step 1. Pick up an insert

1. Select the Ring Adapter (13) (sold separately) with the insert (12) of the required diameter depending on the outer diameter of the lens of your optical device (11) (see Table).
2. The designation 42 mm / 50 mm / 56 mm in the name of the adapter means the lens diameter of the optical device.

For installation of the PSP-30B adapter, see its operating manual.

Step 2. Install the insert into the adapter

1. Apply 2-3 strips of double-sided tape to the outer surface of the insert of your choice (12).
2. Push the insert (12) of your choice into the Ring Adapter (13) until it stops.

Step 3. Mount the adapter on the optical device

1. Move the lever (17) to the OPEN  position.
2. Before installing the Ring Adapter (13) onto the optical device, it is recommended to degrease the lens body of the optical device (11).
3. Mount the Ring Adapter (13) with the insert (12) onto the lens of the daylight optical device (11) as far as it will go.

Step 4. Adjust adapter lever

1. Move the lever (17) from its initial OPEN  position to the CLOSE  position.
2. Loosen the locking screw (15) with a 2mm Allen key*.
3. Tighten the screw (16) with a 4mm Allen key*. The clamping force should be 1.5-2 Nm (13.3-17.7 in-lbs) (use a torque screwdriver) to ensure the lever (17) is correctly tightened, while the Ring Adapter should not move relative to the body of the optical device (11). If necessary, tighten or loosen the screw (16) to operate the lever (17) in the best way possible.
4. Tighten the locking screw (15) as far as it will go.

*Items of PSP B Ring Adapter (available separately)

Selection table for optical device inserts

Step 1. Mount the thermal imaging module on the adapter

1. Remove the protective cover from the eyepiece of the thermal imaging module.
2. Align the protrusions on the adapter (13) with the grooves of the mount assembly (18) of the thermal imaging module and turn the thermal imaging module counterclockwise as far as it will go.

Step 2. Adjust the display position of the thermal imaging module

1. Loosen the screw (14) with an Allen key (S = 4mm).
2. Turn on the thermal imaging module by briefly pressing the ON/OFF (8) button.
3. Align the image center on the display with the image center of the optical device by tilting the thermal imaging module.
4. Tighten the screw (14) as far as it will go. The clamping force should be 5 N·m (44.3 in-lbs) (use the torque screwdriver to check).
5. Move the lever (17) to the OPEN position.
6. Align top and bottom display boundaries parallel to the horizontal axis by turning the adapter with thermal imaging module clockwise or counterclockwise.

7. Move the lever (17) to the CLOSE position.

1. Open the lens cover (1).
2. Turn on the device by pressing the ON/OFF (8) button.
3. Adjust the eyepiece dioptre ring of your daylight optical device until the symbols in the display are sharp. In future, it will not be necessary to adjust the eyepiece dioptre regardless of the distance and other conditions.
4. Rotate the lens focus knob (9) to focus on the visual target.
5. Enter the main menu with a long press of the MENU (6) button and select the desired calibration mode: manual (M), semi-automatic (SA) or automatic (A).
6. Calibrate the image by briefly pressing the ON/OFF (8) button. Close the lens cover when calibrating manually.
7. Select the required amplification level (“Normal” , “High” , “Ultra” ) by briefly pressing the MODE (7) button.
8. Activate the smoothing filterin the main menu to improve the image as the amplification level increases.
9. Select one of the colour palettes in the main menu.
10. Activate the quick menu by briefly pressing the MENU (6) button to adjust the brightness and contrast of the display (for more details, see the Quick Menu section).
11. At high optical magnification, interface elements may be partially or completely invisible. To change the size of the interface, press and hold the DOWN/MODE (7) button.
12. Upon completion of use turn the device off by a long press of the ON/OFF (8) button.

Observation conditions: time of day, weather, type of observation objects affect the image quality. Custom settings for brightness, display contrast as well as the function of adjusting the microbolometer sensitivity level will help to achieve the desired quality in a particular situation.

Warning! Never point the lens at intensive energy sources such as laser radiation emitting devices or the sun. It can damage electronic components in the device. The warranty does not cover damage arising from failure to comply with operating instructions.

The status bar is at the bottom of the display and displays information on the actual operating status of the device, including:

• Color Mode:

– White hot

– Black hot

• Bluetooth
• Calibration Profile (A, B or C)
• Smoothing Filter (displayed when the function is on)
• Amplification level (e.g., Normal)
• Calibration Mode (in Automatic calibration mode a countdown timer will appear instead of the calibration mode icon 3 seconds before automatic calibration begins).
• Power Indication:

– charge level if the device is powered by a battery

 – charge level if the device is charging and powered by a battery

– no battery, the device is connected to an external power supply.

• Video recording status:

– video recording is on

  – pause

• Microphone
• Wi-Fi Connection
• Time
• Auto shutdown function (for example, 5 min)

• Enter the menu with a short press of the MENU (6).
• To select the functions below, press successively MENU (6).

Contrast– press the UP (5)/DOWN (7) buttons to change the display contrast value from 0 to 20.

Brightness– press the UP (5)/DOWN (7) buttons to change the display brightness value from 0 to 20.

• To exit the menu, press and hold down the MENU (6) button, or wait 10 seconds for automatic exit.

The Krypton 2 thermal imagers are equipped with the option to record video and still images (photography) of the observed image by saving them on the built-in memory card.

Before using this feature please set the date and time (see General Settings section).

For information on how to watch recorded photos and videos, see the Stream Vision 2 user manual: Android, iOS.

The built-in recorder operates in two modes:

Video Mode. Video Recording

1. Switch to Video mode by pressing and holding the UP/REC (5).

2. The iconand the remaining recording time appear briefly on the screen in the format HH:MM (hours:minutes), for example, 5:12. In the status bar, the video recording status is displayed continuously.

3. Press the UP/REC (5) button briefly to start video recording.

4. When the video recording starts, the icon will disappear and the REC icon and timer in MM:SS (Minutes:Seconds) format will appear.

5. Press the UP/REC (5) button briefly to pause or resume video recording.

6. Press and hold the UP/REC (5) button to stop video recording.

7. Video files are saved to the built-in memory card after the video recording has been stopped.

8. Press and hold the UP/REC (5) button to switch between the video and photo modes.

Photo Mode. Capturing a photo

1. Switch to Photo mode by pressing and holding the UP/REC (5)

2. Press the UP/REC (5) button briefly to take a photo. The image freezes for 0.5 sec while the photo is saved to the internal memory.

Notes:

• You can enter and navigate the menu during video recording.
• The recorded videos and photos are saved to the built-in memory card of the device in the formats img_xxx.jpg (photos) and video_xxx. mp4 (video) where xxx is a 3 digit counter.
• The counter for multimedia files cannot be reset.

Attention!

• The maximum duration of a recorded video file is five minutes. After this time expires, the video is recorded to a new file.
• The number of files is limited by the device’s built-in memory and video compression ratio.
• Regularly check the free capacity of the internal memory and move recorded footage to other storage media to free up space on the internal memory card.
• In case of a memory card error, you can use the format function in the General Settings section of the main menu.
• When the Display Off function is activated, video recording continues to run in the background.

The device has a function enabling wireless communication with external devices (smartphone or tablet) via Wi-Fi.

• Turn on the wireless module in the WI-Fi Activationmenu option (see the Wi-Fi section).

Wi-Fi is displayed in the status bar as follows:

Connection Status	Indication on the status bar
Wi-Fi is switched off
Wi-Fi connection is in progress
Wi-Fi is switched on, no connection with device
Wi-Fi is switched on, device connected

• The device is recognized by an external device as KRYPTON2_XXXX where XXXX are the four last digits of the serial number.
• After entering the password on the external device (see the  Password Setup subsection of the Wi-Fi section for more information on setting a password) and setting up a connection, the iconin the status bar changes to.
• The Wi-Fi function will turn off automatically if there is not enough battery power for Wi-Fi. The battery icon will turn red  and flash. To use the Wi-Fi function again, you need to charge the battery.

This function darkens the screen, which aids the user’s concealment. However, the device stays on.

When this function is in use, the device switches to the standby mode, which allows it to be switched on instantly.

1. When the device is on, press and hold the ON/OFF (8) button. The display will turn off, the current time and the “Display off” icon will appear.
2. Turn the display back on with a short press of the ON/OFF (8) button.
3. When you press and hold the ON/OFF (8) button, the display shows the “Display off” icon with a countdown. Pressing & holding the button down for the duration of the countdown will power the device off completely.

1. Connect one end of the USB cable (20) to the USB Type-C port (10) of your device and the other end to the USB port of your PC / laptop using a USB Type-A adapter.
2. Turn the device on with a short press of the ON/OFF (8) button (a device that has been turned off cannot be detected by your computer).
3. Your device will be detected by the computer automatically; no drivers need to be installed.
4. Two connection modes will appear on the display: Power and Memory Card (external storage device).
5. Select the connection mode with the UP (5)/DOWN (7) buttons.
6. Confirm the selection with a short press of the MENU (6) button.

Power

• In this mode, a PC/laptop is used as an external power supply. The status bar shows the icon . The device continues operating and all functions are available.
• Battery recharge feasibility depends on your computer’s USB port.
• When the USB is disconnected from the device when in the Power mode, the device keeps operating with the Battery Pack if it is available and sufficiently charged.

Memory Card (external memory)

• In this mode the device is detected by the computer as a flash card. This mode is designed for work with the files saved in the device’s memory. The device’s functions are not available in this mode; the device turns off automatically.
• If video recording was in progress when the connection was made, recording stops and the video is saved.
• If the device is in Memory Card mode and is disconnected from USB, the device will remain on.

Install the Stream Vision 2 application to download files, update firmware, control the device by remote control and broadcast images from your device to a smartphone or a tablet via Wi-Fi.

We recommend using the latest version – Stream Vision 2.

You can find further guidelines on Stream Vision 2 here.

Download from Google Play

Download from App Store

Find answers to frequently asked questions about using Stream Vision 2 here.

Stream Vision 2 Manual

Android

iOS

1. Download free Stream Vision 2 App in Google Play or App Store.
2. Connect your Pulsar device to your mobile device (smartphone or tablet).
3. Launch Stream Vision 2 and go to section “Settings”.
4. Select your Pulsar device and press “Check firmware update”.
5. Wait for the update to download and install. Pulsar device will reboot and will be ready to operate.

Important:

• if your Pulsar device is connected to phone, please turn on mobile data transfer (GPRS/3G/4G) to download update;
• if your Pulsar device is not connected to your phone but is already listed in “Settings” > “My devices” section, you may use Wi-Fi to download update.

Find answers to frequently asked questions about using Stream Vision 2 here.

Is your firmware up to date?

Click here to check the latest firmware for your device.

It is recommended to carry out a technical inspection before each use of the device. Check the following:

• The device appearance (there should be no cracks on the body).
• The state of the objective and eyepiece lenses of the thermal imaging module (there should be no cracks, grease spots, dirt or other deposits).
• The state of the rechargeable battery (it should be charged) and the electric contacts (there should be no signs of salts or oxidation).
• The controls should be in working order.
• The thermal imaging module is properly and firmly fixed on the optical device.

Maintenance should be carried out at least twice a year and include the following steps:

• Wipe the exterior metal and plastic surfaces with a cotton cloth to remove dust and dirt. To avoid damage to the paint coating, do not use chemically active substances, solvents, etc.
• Clean the electrical contacts of the rechargeable battery on the device using a non-greasy organic solvent.
• Check the eyepiece and the lens and if required remove dust and dirt from the optics (preferably using a non-contact method). Cleaning of the exterior surfaces of the optics should only be done with products specifically designed for this purpose.
• Always store the device in its carrying case in a dry, well-ventilated space. For prolonged storage, remove the batteries.
• Avoid getting repellent on the housing of the device. This may damage the appearance of the housing coating.